How to Draw a Lamborghini Car
Their vertical door conversion kit if you are interested in trying to install, a warning, but it’s tricky here is a guide to assist in the procedure can be
1. Lift the hood, the front wheel to the left and right sides of the shield is removed.
2. Doors, doors and door frames, remove the rubber hose to connect the wires in the open state (with friction tape the two ends of the wires all cut and finish to record a given number of wire is enough, if that ‘S is cut out of here, do not need are cut) and then remove the rubber hose to the wire.
3. Remove the factory closed doors with the top door hinge.
4. The placement of the test apparatus, and draws Arm swing mode of transportation, pay attention and ensure the swing arms 90 ° does not touch the shield or bumper. So, the mechanism can be tested as a shield to be in the proper height.
5. Installation location of the chassis sits flat on the ground or to interfere with the base plate to ruin all the extrusions. You also need to grind and, depending on the base plate and door plate can be cut.
B. After crushing the installation location to test the proper distance behind them and move the swing arm to prevent the base plate to identify and observe the place to be. In this situation, you have cut or hammer along the perimeter until it does not interfere, and then if appropriate to draw a line around the base plate, must be
Small space between the surface in contact with the chassis and the car C. There is not enough room to install. It can be solved as follows: to determine the location of the base plate, with it in the proper position to draw a line around the base plate and then slide the base plate below the surface to be cut along the perimeter.
6. Make sure to keep the location and space. The default position of the painted arches paneitneun safe to cut it. To accommodate the arch to cut slots in the chassis and the base plate at the bottom of the application, if on the surface of the chassis using the hex key to adjust the additional space.
7. Then you will get welded for the surface protection of the surface except the surface of the base plates, doors and welding deflection paper will cover the rest of door mechanism.
8. Chassis door mechanisms, door locations, and clings well to move
After re-testing, the base plate and door plate welded around the perimeter of the attraction in two directions, horizontally and vertically will be appropriate. You think it’s strong enough to weld to remove the hinges when the door down. You observe and swing it out the door manually, the maximum for the correct operation and to test whether the location. Now, out the door, the door mechanism to adjust the motion of the screws, safety set screw and door height screws etc. can be created.
9. Check swing arm and shield or fender the position space, movement and cut off lottery. And re-test in order to provide clearance for the swing arm to cut the inner lip.
10. Once you do, shut the door muneulgiguui lifting and dropping, jobs and placements, such as openness and satisfaction, from the top to the bottom of the hinge mechanism, the center axis of the hammer to remove the following statement. Entire perimeter of the base plate and door plate is a strong weld. (Parts must be interrupted during welding of high temperature yigeulyigeul).
11. Grinding and welding, surface scuff and undercoat paint and top coating masks to prevent rust.
12. Heavy waterproof grease and then close the door hinge alignment holes and holes in the door mechanism to mediate the movement of the center axis from top to bottom, form the surface rubeuneun then hammer it well and smoothly.
13. When the door is open to the maximum angle to clear the wires. If the wire is not enough to measure the length needed to connect to other lines. Cutting and insulating tape for the number of joints must be connected to the mask. Plastic and string at the bottom of the swing arm with a fixed cluster wire plaited.
14. Open the door to the highest point on the rotation, swing arm and gas spring connecting plot threads, each with gas spring screws and then the two ball joint ball joint will get mounted on the chassis, determine the location and displays it.
15. Insert the gas spring ball screws so the door connecting the gas spring connecting plot forms a hammer or grind the fixed position and fixed in place plot separates good weld. Paint dust.
16. Open the door to the highest point of connection to the gas spring ball points plotted at the same time firmly screw locks swing arm, with a starting point. Contact the movement and testing. Eighty-two parallel swing and when the door is moving down the gas spring or other parts should not interfere.
17. The door is closed and fully comply with the latch on the door until the door is shut down to test the horizontal movement. All exit doors when the horizontal contact with the door mechanism no longer interferes with the shield or not to adjust until the safety arch. Then the safety arch until you come out of the inside of raising eight horizontal motion screws to correspond to that angle set. These two adjustments closer, more durable, and the vertical position up to the door will feel relax. Your shield or on other parts of this statement does not conflict with providing the desired height adjustment of the vertical height limiter is set.
18. Door panels and / or door metal shield that provides views or if you need to cut it up too close to the shield. If you need to cut the door panel to permit the first line is displayed. Then re-upholstery bark, and cut a new edge with spray adhesive and wrap through the interior.
19. Screw all screws and glue to seal the points, not all of which interfere with test again until you are satisfied.
20. Shields, fenders and hood, mounted and put it down. This will complete the installation.
How to Draw a Lamborghini Car